• English
  • Hindi

Combination Set 2019-01-23 10:01:00

Combination Set


Combination set is used to measure the job's angle, to remove the centre of the round job, it has 4 parts.


1. Blade Rule

2. Square Head

3. Protector Head

4. Centre Head

Blade & Rule

It is made with high carbon steel and alloy steel and on hard temper. A key way is cut in the canter of this rule. With the help of which the three head salads do.


Square Head

This is made of cast steel. If the blade or rule is set in it, it can easily check an angle of 90° and 45° degree. It is also used to check depth to measure. The square head also has a spirit level. With the help of which it can easily check the surface level. And it fits on the scrubber, with the help of which the line can be drawn.


Protector Head

The protector head is made of cast steel in which a disk is located, which has a mark of 0° to 180°  Which is used to check the angle.

Canter Head

The centre head cast is made of steel and the angle between its sides is 90 degrees. With this help, you can easily check any circular job canter


1. Metal of Blade of Combination Set - High carbon steel and alloy steel


2. Angle between the two sides of the square head - 90° and 45°


3. Which part of the compartment set is attached to the scribbler - Square Head


4. Which part of the compartment set is used to remove the centre of the round job - centre head


5. How many degrees are done on the dumps of the composition set - 0° to 180°


6. Which parts of the composition set are used to measure and check the depth of the job - Rule and Square Head


7. Combination set is used - to check the angle


8. The centre head is made in which angle - 90°


Click here to watch the video of ITI Trade

Click Here

Click for ITI Technical Notes

Click Here

Multiple choice pdf file

Click Here

​​​​​​​Join us on Telegram

Click Here

कंबीनेशन सेट 2019-01-23 10:01:00


Combination Set कंबीनेशन सेट





कंबीनेशन सेट का प्रयोग जॉब के कोण को मापने में गोल जॉब का सेंटर निकालने के लिए किया जाता है इसके 4 भाग होते हैं

1. ब्लेड  रूल

2. स्क्वायर हैड 

3. प्रोटेक्टर हैड 

4. सेंटर हैड


ब्लेड या रूल Blade & Rule




इसे हाई कार्बन स्टील व एलॉय स्टील से बनाकर हार्ड टम्पर पर किया जाता है इस रूल के सेंटर में एक key way कटा होता है। जिसकी सहायता से तीनों हेड सलाइड करते हैं।


स्क्वायर हैड Square Head


​​​​​​​​​​​यह कॉस्ट स्टील से बनाया जाता है। यदि इसमें ब्लेड या रूल को सेट कर दिया जाए तो यह 90° और 45° डिग्री के कोण को आसानी से चेक कर सकता है। इसका प्रयोग गहराई मापने के लिए चेक करने के लिए भी किया जाता है। स्क्वायर हेड में स्प्रिट लेवल भी लगा होता है। जिसकी सहायता से यह सरफेस लेवल को आसानी से चेक कर सकता है। तथा इसमें स्क्रबर पर फिट रहता है जिसकी सहायता से लाइन खींची जा सकती है।






प्रोटेक्टर हैड Protector Head



प्रोटेक्टर हैड यह कास्ट स्टील का बना होता है जिसमें एक डिक्स लगी होती है जिस पर 0° से 180° डिग्री के निशान बने होते हैं। जिसका प्रयोग कोण को चैक करने के लिए किया जाता है। 


सेंटर हैड Canter Head



सेंटर हैड कास्ट स्टील का बना होता है इसकी दोनों भुजाओं के बीच का कोण 90 डिग्री रखा जाता है। इसकी सहायता से किसी भी गोल जॉब का सेंटर को आसानी से निकाल सकते हैं




1. कंबीनेशन सेट के ब्लेड की धातु - हाई कार्बन स्टील व एलॉय स्टील 


2. स्क्वायर हैड की दोनों भुजाओं के बीच का कोण - 90° 45°


3. कंबीनेशन सेट के किस भाग के साथ स्क्राइबर लगा होता है - स्क्वायर हैड


4. गोल जॉब का सेंटर निकालने के लिए कंबीनेशन सेट के किस भाग का प्रयोग किया जाता है - सेंटर हैड


5. कंबीनेशन सेट के डिक्स पर कितने डिग्री बनी होती है - से 180°


6. जॉब की गहराई मापने व चेक करने के लिए कंबीनेशन सेट के किस पार्ट्स का प्रयोग किया जाता है - रूल व स्क्वायर हैड


7. कंबीनेशन सेट का प्रयोग किया जाता है - कोण को चेक करने के लिए


8. सेंटर हेड किस कोण में बना होता है - 90°



आईटीआई ट्रेड की वीडियो देखने के लिए यहां क्लिक करें

नोट्स के लिए क्लिक करें

टेलीग्राम पर हमसे जुड़ें

Share Share
12609 Views

© 2018 IT Info Trade. All rights reserved || Terms & Conditions